What good is a Ring contact sensor if you can’t put it in the right place in your home?
When it comes to installing touch sensors on doors and windows, there is a lot of fear. Because of their poor alignment, they will be unable to offer the level of protection you need. This is a good thing since these sensors are quite forgiving in terms of how they are attached.
It is not necessary for ring contact sensors to be flush installed. As long as they are no more than 1 inch apart, they may be installed in any orientation. Even removing the magnet from one part of the sensor may be used to install the sensor in various positions.
Let’s talk to the Ring contact sensor.
The Ring Alarm System is what it says it is.
Box for the Ring Security Alarms
Ring is one of the finest smart home security systems available. Even while Ring’s doorbell cameras are the company’s best-known product, it’s the company’s smart home system that has propelled Ring to prominence.
This alarm system will notify you if your washing machine floods your laundry area, open doors, and other potential dangers. At a minimum, this alarm system comes with a keypad, the Ring Alarm base station, and a few sensors.
The following is a comprehensive list of the extras that may be included in your Ring alarm system.
Keypad
Sensors Using Contact
Motion Detection
Sensors for Flood and Freeze
This is the Ring Alarm’s main station.
Additionally, the Ring doorbell and Ring cameras may be used in conjunction with these devices, and they all operate with Amazon’s Alexa voice assistant.
The Ring contact sensor is the most exciting element of this jigsaw. Let’s take a deeper look at what’s going on inside of this little gadget.
The Ring Contact Sensor is housed inside
2nd generation ring contact sensor
In order for the Ring alarm system to work, it needs Ring contact sensors. In fact, some may argue that these components constitute the heart of the alarm system and its most crucial aspect.
If you have Ring contact sensors, you’ll know when doors and windows are opened. Sensors built inside the components allow them to function. The electronics and batteries are located in the active component, whereas the magnet is located in the passive component.
You’ll get a notice on your phone or tablet if the magnet travels too far from the electrical component.
Is it necessary to flush mount the Ring Contact Sensor?
The Ring contact sensors don’t need to be flush mounted. In fact, you can place them as far apart as 1 inch and they would still work. Advanced users have even removed the magnet from the side without the electronics, allowing for a wide range of mounting options.
Ring contact sensors may be mounted on your doors and windows in a variety of ways. Let’s have a look at some of the simplest and most complicated methods to attach these sensors.
Uneven Surfaces: How to Mount the Ring Contact Sensor
It’s possible that the mounting surfaces of your Ring contact sensors will be flush, but that’s not always guaranteed. You don’t have to worry about your sensors touching when they line up because of this:
My front door has a Ring Contact Sensor installed.
While each house has its own eccentricities, we have to learn to work around them at times.
Throughout this guide, we’ll walk you through the process of installing Ring sensors in your house.
Mounting Offsets of Up to One Inch
Prior to moving on to more advanced mounting techniques, let’s have a look at the easiest approach to install around tricky doors and windows.
It’s a good idea to give up to an inch of space between each of your Ring touch sensors.
One inch may be applied in either direction. They may be spaced 1 inch apart horizontally, 1 inch apart vertically, or at an angle of 1 inch. The internal magnets can only work at a distance of 1 inch. In order to keep your alarms from going off, the magnets need to be no more than 1 inch away from the alarm clocks.
My Ring Alarm’s event log shows a few tampering errors.
If you’re going to use offset mounting, you’ll have to experiment with it a little. When attaching Ring contact sensors, this 1 inch is a good starting point. If the magnets in your gadget are very strong, you could be able to gain more or less distance from yours. It all depends on how strong yours are.
You may get a leg up on the competition by installing a few test pieces. Sticky tack, which can be easily removed, is a great way to temporarily mount your Ring sensors while you test their fit and functionality.
Screw them in or use the included double-sided tape to quickly and easily mount them once you’ve worked out how they’ll fit.
Using a Right Angle Bracket
As it turns out, the Ring sensors don’t really need to be flush with each other.
If the Ring contact sensors are spaced apart, or if they meet at an angle other than right, or if they meet at any other angle, it makes no difference.
A garage door with a Ring Contact Sensor installed is an excellent example.
For the magnet to work, they must be separated by no more than one inch.
As a result, they can be installed at a right angle. For doors with ornate moldings or specific window trims that don’t allow for flat attachment of Ring contact sensors, this may be a suitable solution.
Other mounting angles are acceptable as long as the sensors are not more than one inch apart. Installation on a beautiful door or even an exterior gate might take use of this feature.
Shims or Wedges may be added.
Truth be said, This is one of the most appealing aspects of Ring technology. Offset mounting and right-angle mourning detract from the aesthetic purity of the design. Fortunately, wedges or shims may be used to keep your sensors flush.
You may use tiny pieces of angled wood, such as wedges and shims, to ensure that your work is level. A shim is any substance placed beneath the short leg of a shaky table to provide support and balance. Ring contact sensors may be used in the same way.
In order to attain an even fit, you’re going to have to do some arithmetic or some trial and error. Measure the angle at which you need to modify your contact sensor, or you may purchase various shims so that you can estimate and get it right:
Shims may be purchased where? Shims of various sizes and materials are likely to be found at your local hardware shop. Considering that this is a commercial item, expect to buy it in bulk.
The spare wood lying around your home may also be used to construct your own shim. By asking around to see if anybody you know has any extra shims or scrap wood sitting around, you may be able to get some freebies.
Another option is to 3D print a shim with the precise dimensions and angle needed for your project.
The contact sensor may be attached to the shim using double-sided tape and the shim can be attached to the wall. This may help you get past some of the most difficult mounting issues, such as ornamental molding or oddly angled windows.
3D-Printed and Customized Spacers
The Ring contact sensor is one of the finest features of the Ring since it simply requires that the internal magnets align. There is no requirement for the sensor to be attached to your door or window, as long as the magnets separate from each other.
As a result, it is possible to utilize bespoke or 3D printed spacers to aid in the magnetization process. For doors that are recessed into the frame, this is very helpful.
You may have required the sensor to connect to the edge of the frame since your door was 2 or 3 inches away from it. Filling the void may be done with a 3D printed riser.
A wooden Riser is an alternative if the 3D printed style doesn’t go well with the rest of your décor. Adding a piece of material to support your touch sensor may be painted or stained to match your door, making it blend in and reducing the visual noise.
Removing the Magnet is a physical process.
The rear of a Ring Contact Sensor with adhesive and screw holes.
The Ring contact sensor’s marketing wizardry is on display here. When you acquire the Ring contact sensor, it seems that you’re paying for two separate technical devices. Since it’s made up of two parts, you’ll need both of them to use it.
There is just one technical device and one magnet in the nice plastic shell that you’re paying for.
That’s correct, the other half of your Ring contact sensor is nothing more than a magnet enclosed in a plastic casing. Removing the plastic casing gives you a lot more flexibility when it comes to mounting the magnet on your Ring contact sensor if it won’t fit correctly on your door frame or window.
For old-fashioned windows, you may even stick it straight to the glass itself if you have an uncomfortable molding around the door to work with. To remove the huge plastic housing, remove the magnet and you’re free to place it where you like.
The most important thing to remember is that you’ll need to use double-sided tape to attach this magnet.
There will be no mounting brackets for screws, since there is no longer any housing. Because you won’t have the case to guide your alignment any more, you’ll have to conduct some trial and error to ensure the magnet is correctly positioned.